NCCER Test Questions and Answers 100% Pass

ball-peen hammer

another name for a machinist’s hammer

sledge hammer

a heavy-duty tool used to drive posts or other large stakes

60 degree angle

the proper angle for the edge of a cold chisel

reed and prince

A screw that comes to a relatively sharp point at the base of its drive socket

six

number of sides of a hexagonal shape

smooth jaws

How is a spud wrench different from a pipe wrench

speed handle

to quickly run a nut onto a bolt that resists spinning it on with the fingers, you can drive the socket with one.

side cutters

another common name for lineman pliers

vertical distance

Because of its stiffness, a folding ruler is better than a cloth or steel tape for measuring

highly reflective surface

One situation that can make a measurement with a laser inaccurate is measuring to a

perfectly vertical

When an object is plumb, it is

45 degree angle

In addition to level and plumb, some spirit levels can check a

laser level

To check conditions over a significant distance, such as a building foundation or longer distance, the best level to use is a

rip saw

Which of the following saws would likely have the fewest teeth per inch, resulting in the largest teeth?

back saw

The best designed saw for cutting miter joints is a

protect the surface

When using a utility knife, place piece of scrap material under the object you are cutting in order to

self retracting

The safest kind of utility knife is one with a

fiber glass

Shovels typically have handles made of wood or

fixed firmly to the handle

Before using a pick, check to be sure that the head is

automatic brake

A chain fall locks its elevated load in place using

short ground distances

Cable come-alongs are used to move loads

hand screw clamp

Because of the shape of its jaws, which clamp can spread clamping pressure over a wider area than the others?

Robertson

A square socket screw head

Spring Clamp

A “clothes pin” clamp usually used for minimal clamping pressure

Coping Saw

Used for delicate work involving mouldings

Nccer test questions and answers quizlet
Nccer test questions and answers pdf
nccer basic safety test answers
nccer module 1 test answers
nccer safety test
nccer test answers module 2
nccer math test answers
nccer test review basic safety

• When everyone associated with a company has a positive attitude about safety, they have developed a strong safety ______________.culturesystemrule bookpolicy
• 2. Multiple-choiceAuto-convertEdit5 seconds1 pointA strong safety culture can lead to a low _____ rate which means a company is not constantly having to replace employees.reductionexemptionturnoverwhisltlblower
• 3. Multiple-choiceAuto-convertEdit5 seconds1 pointSafety training is important because _____ is a learned behavior and attitude.educationsafetyemploymentworking
• 4. Multiple-choiceAuto-convertEdit5 seconds1 point____ conditions like poor lighting, loud noise, and missing guards on machines can lead to accidents.Unsafecommonacceptabledesirable
• 5. Multiple-choiceEdit5 seconds1 pointWhen it comes to On-the-Job safety, you should…rely on your boss to keep you safetake responsibility for your own actionshope that others around you will keep you safecontact OSHA to find out how to be safe
• 6. Multiple-choiceAuto-convertEdit5 seconds1 pointOne of the main purposes of good housekeeping in the shop is to…reduce hazardssimple aestheticskeep busymake the boss happy
• 7. Multiple-choiceEdit5 seconds1 pointA primary purpose of OSHA is to…test new products to make sure they are safe to useprotect the safety and health of American workerspublish safety rules for employers and employeesoversee certification of equipment operators
• 8. Multiple-choiceAuto-convertEdit5 seconds1 pointA _____ person can identify unsafe conditions on a jobsite and has authority to correct them.LicensedCertifiedQualifiedCompetent
• 9. Multiple-choiceAuto-convertEdit5 seconds1 pointAn on-the-job safety event is categorized as an _____ if it could have caused an injury, but was caught in time.injuryaccidentincidentinconvenience
• 10. Multiple-choiceAuto-convertEdit5 seconds1 pointAn on-the-job safety event is categorized as an _____ if it causes property damage.injuryaccidentincidentinconvenience
• 11. Multiple-choiceAuto-convertEdit5 seconds1 pointThe portion of the federal law that requires employers to provide a safe working environment for employees is called…the Whistleblower Actthe General Duty Clausethe Safety Standard Actthe MSDS Act
• 12. Multiple-choiceAuto-convertEdit5 seconds1 pointIf you feel that you have been discriminated against by an employer for asserting your rights under OSHA, you have ______ to file a complaint.30 days6 months12 months3 years
• 13. Multiple-choiceAuto-convertEdit5 seconds1 pointIf an accident on a jobsite results in the hospitalization of 3 or more workers, employers must report it to OSHA within ________ .4 hours8 hours24 hours48 hours
• 14. Multiple-choiceAuto-convertEditThe act of breaking a job down into its component parts or steps in order to identify potential hazards is referred to as…a Job Safety Analysisa Safety Management Systema Corporate Safety Culturean OSHA Inspection
• 15. Multiple-choiceAuto-convertEdit5 seconds1 pointYou can determine ______ by measuring the probability of exposure to a hazard and a resulting accident.dutiesturnover ratestaffing needsrisk